Xhorse VVDI Key Tool Plus Pad

  Here comes a similar problem: I made all key lost bmw e70 x5 with  xhorse vvdi key tool plus . I read flash and eeprom from cas3+ by welding and saved it. After i start process akl without isn, add key (315mhz). Read immo status, and saw the key was already programmed. But first thing is remote don’t work, and car didn’t start. Only starter run. And I have errors in DDE by launch 2E3C and 4D2D. I read the problem can be wrong isn by dde and cas. I don’t read isn in DDE, i start process without isn as suggested to me key tool plus. Please any suggestions. Solution: Do a Synchronization CAS with DDE with Key tool plus , ISTA or your Launch X431 scanner. Read the key info from CAS module, with the information unlock the key that you made. You can unlock it with the read info from the CAS. It’s a cas 3+ you will need the ISN when your key is unlocked rewrite it utilizing a different position in the CAS with the ISN. Do not skip that step once you are finished...

  Toyota Auris 2013 all keys lost is done by   xhorse vvdi key tool plus   and   8A non-smart key AKL adapter . Auris 2013 it’s 8A H key. None smart, no G key. Profile was va2. Cut on  xhorse dolphin xp005  machine. Got keycode from toyota, you also have the keycode on the car papers. Ignition coil read as 4d. I tried all tools like zedfull, Im608, londor to do smart box reset nothing worked. When choose G chip 72 system i got a connection but it was stuck on communicating… When trying to do Smartbox reset. Then I took xhorse 8A AKL adapter but Auris schema was nowhere described, found an ign2 relay took it out and connected battery and ignition coil. I took out the ign2 relay and but j3 in it I could find a schema nowhere. I did not select smart key and it was not g key. I got a successful read and was able to program  vvdi super chip . Car started. FYI: TOYOTA AURIS 2010-2012 Transponder Texas Crypto DST 80-bit / DST80 / Toyota G-...

  How to use   Xhorse VVDI Key Tool Plus Pad   to program a new BE key for Mercedes Benz W203 via IR? Follow the steps below to learn.   Step1. Read Password Immo programming >> Europe >> Benz >> Select from system >> EIS Tools >> Start programming >> W203, 463, 639(K) >> Read the lock(EIS) data >> IR   Insert  IR Adapter  to car. Take out and insert again if already inserted.   The password of the lock is detected. Press “Yes” to save data file.   Password read by infrared? W209/211(CPU HC12), R171 and W203/215/220/230(CPU HC08) EIS support infrared reading of password. This function supports adding and lose all. This function does not required points or online calculation. It takes about 1-4 minutes to read the password directly through infrared. If the final reading fails, please use other methods to obtain the password. Press “Yes”.   Reading password via IR… Password has been successfu...

  Question: I have a problem resetting  xhorse vvdi super chip xt27 a to MQB chip. Tried 10 different chips with same result.     Answer and solution: Only  VVDI Super Chip XT27B  ​chips could be set as MQB. Check XT27A vs XT27B http://blog.vvdishop.com/xhorse-vvdi-super-chip-xt27b-vs-xt27a/ How to set Superchip XT27B as MQB chip with  vvdi key tool plus Go to Special Function-> Set type of VVDI Super Chip-> Set as MQB

  Xhorse VVDI KEY TOOL PLUS   tutorial: how to program Audi S5 2010 BCM2 All Keys Lost via OBD II, no opening ECU. Main steps: Read BCM2 Data Make dealer key Learn key Procedure: Go to Immo Programming- Europe- Audi- Auto diagnose model It is 5th generation immobilizer system Select Read BCM2 data->OBD identify BCM2 type connect key tool plus with vehicle via OBD Identify software version and key information This version 0327 supports OBD to read BCM2 data (add key and all keys lost) Go back to the previous menu, select Read by OBDII->Read BCM2 data (OBDII) Read software number 0327, key number and key info. Disconnect BCM module from power for 2-3 seconds and reconnect Then return OBD read BCM function Save BCM2 data   Step 2: Make dealer key Then select Make Dealer key function Select have BCM2 data and all keys lost situation Load BCM2 data in step 1 Put a new key into the  xhorse key tool plus  programmer Reading key info and programming key in the pro...

  New test report:   xhorse vvdi key tool plus   adds new centralized remote control to a VW Golf 7 year 2017 MQB key successfully. Using  xhorse MQB48 smart Key  XSMQB1EN. Did the pin code calculation by following steps: 1:Automatically diagnose models 2:read eeprom 3:read immo data 4:generate dealer Key 5:Learn Key Programming success