Xhorse VVDI Key Tool Plus Pad

  Problem:   I was able to use   VVDI Key Tool Plus   Pad +   Toyota 8A AKL Adapter   to read out immo data, and succeed in generating a   XM38 Smart Key . But this key is unable to emergency start the car. Any ideas?   Solution Please noted to generate XM38 to corresponding VIN of smart card before Toyota 8A all keys lost programming. Eg. 2020 Toyota Camry – 0010 version smart card 2015 Lexus – 2110 version smart card. (Please ask for the professional if you don’t know the version) Steps Generate to the corresponding version of smart card; Generate emergency key with immo data. Full operations please refer to Xhorse VVDI 8A Adapter Program 2020 Toyota Highlander All Keys Lost   For some special cases, after generating smart card version, it’ll need to remove battery, then go on making an emergency key.   Any questions about VVDI 8A Adapter please contact us. www.vvdishop.com

  Pay attention to delete key functions of the new   Xhorse XD8ASKGL Toyota 8A AKL Adapter . We can add and delete older Toyota 8A smart keys on the same car without limitation. The key can be programmed to another car after being deleted. But for some latest Toyota with 8A and 4A smart keys, the deleted key cannot be programmed again, even original keys. The Delete key function is used to delete all absent keys. Keys that do not touch the ignition switch will be deleted and cannot be registered to use.   Always do ‘Add Smart Key’ operation when we add a key or do all keys lost  unless you are requested to do AKL.     When executing  Backup Smart Box EEPROM Data  and program key,   vvdi key tool plus  will ask to load smart box eeprom data, after you load eeprom data, the deleted key cannot be programmed again. If didn’t do Backup eeprom data, the deleted keys can be learned to car. For old Toyota 8A proximity, we can only...

  Problem: I was working on an audi A5 all keys lost. I tried to read bcm2 with my  vvdi key tool plus  and soldering free adapter but key tool plus keeps telling me that failed to connect with the adapter. I correctly connected the adapter with DB15 cable. Don’t know why KTP still can’t connect to the adapter. It’s my first time using  bcm2 adapter  with Keytool plus. I was able to read the bcm2 with same adapter but with the  vvdi prog . Solution: 1).  Check if the adapter is connected to the board properly. If you look at where the pogos are supposed to go, line them up first before putting the side clips on it will work. http://blog.vvdishop.com/connect-xhorse-audi-bcm2-adapter-with-vvdi-key-tool-plus/   2). If check all the pin connections and they all good. The adapter is right. Try to update vvdi key tool plus software/firmware to latest version. We had a customer solve this error by updating the software to V1.8.0 and everything works...

  Problem:  I have a problem generating Ford F150 ID49  remote  with  xhorse vvdi key tool plus . It says the latest remote does not support 868, 902mhz frequency. Answer: The latest remote cannot generate 868mhz, 902mhz remote. Use the old remote before v2.0 to generate. You cannot tell the remote version from the appearance. You can identify the remote versions xhorse key tool plus. http://blog.vvdishop.com/xhorse-vvdi-new-smart-remote-vs-old-smart-remote/

  This is a quick guide on how to use Xhorse VVDI 8A Adapter to program 2020 Toyota Highlander all smart keys lost. No PIN code in need, fast & safe. The operation also works for other supported 2017+ Toyota models.   Supported models please check: Xhorse 8A 4A AKL Adapter for 4A 8A Page4 All Keys Lost Bypass PIN   Tools Required Toyota IMMO box module VVDI Key Tool Plus Pad XM28 Smart Key Xhorse Toyota 8A/4A AKL Adapter   Procedure Step1.  Remove IMMO box from the vehicle, plug VVDI 8A adapter into the module, then connect to VVDI Key Tool Plus.   Step2.  Use VVDI Key Tool Plus to backup IMMO data from module.   Step3.  Generate an emergency key with Toyota XM series remote.   Step4.  Use the new generated key to start vehicle.   Step5.  Through add key function to make a new key.   Completed! VVDISHOP.com customer also already try AKL 2019 TOYOTA ALPHARD, 2019 TOYOTA HARRIER, 2019 TOYOTA SIENTA, with Key tool pl...

  Problem: Xhorse vvdi key tool plus  failed to read BMW CAS3+ IMMO data with  solder free adapter . It said self-test vpp error. Any input? Solution: Firmware issue. Run a firmware upgrade and try again.

  This is a guide on how to change Mercedes Benz   VVDI BE Key  frequency with   Xhorse VVDI Key Tool Plus   Pad. In this way, users can modify BE key frequency between 315Mhz & 433Mhz.   Operation Steps Path: Immo programming >> Europe >> Benz >> Select from system >> Read write key >> VVDI BE key >> Start programming Insert  Xhorse BE Key Pro  into VVDI Key Tool Plus infrared remote port. Read BE key frequency at first. This key frequency is 315Mhz. Go back to set BE key frequency. Here’s allowed to set 315Mhz or 433Mhz. Click on 433Mhz. Set frequency success! Check BE key frequency again. It has been changed to 433Mhz. Successfully done! Quite an easy job, 1 minute is enough. You can also change the frequency by removing the resistor. Check  http://blog.vvdishop.com/change-xhorse-vvdi-be-key-frequency/ Read also: Change Xhorse MB FBS3 Smart Key Frequency with VVDI Key Tool Plus

Xhorse VVDI Key Tool Plus  is a good tool to successfully add BMW E60 key via OBD in 1 minute. Following I’m gonna show you.   Read & Save Key Info Immo programming >> BMW >> Automatically diagnose models >> Read key information Please insert the key into ignition switch. Connect the vehicle & key tool plus well. Press “Yes” to add key.   Confirm key info, press “Yes”.   The dealer key should be taken away from ignition switch. If key is keyless, please move it out of car. If there’s no key in ignition, continue anyway. Press “OK”.   Save key file.   Program New Key Prepare dealer key with programmer >> Select a blank key position: Key4 Put new key into  Xhorse Key Tool Plus  Programmer. Is the current key a smart key? No   Key make okay and locked. Please use it to start the car. If cannot start engine, use “Add key” function to add the dealer key to CAS system. If key can start engine, but keyless not working...