Program Chevy Cruze 2010-2016 Key with Xhorse VVDI Key Tool Plus

How to use Xhorse VVDI Key Tool Plus Pad to add a Chevrolet Cruze 2010-2016 ID46 key by OBD? Following I’ll show the operation process step by step.

Program Remote

Put a XSKF21EN Smart Key into VVDI Key Tool Plus slot, press

Remote program >> Chevrolet >> Cruze >> Cruze KeylessGo ID46(433) >> Generate

Wait writing data until 100%…

Burn success.

xhorse key tool plus Chevy Cruze 2010-2016 Key 1

xhorse key tool plus Chevy Cruze 2010-2016 Key 2

xhorse key tool plus Chevy Cruze 2010-2016 Key 3

Read PIN Code

Immo programming >> Chevrolet >> Read PIN code >> Type 1(BCM) >> Start programming >> Read PIN code

For mechanical key, please switch ignition off and remove the key, then insert the key and switch ignition on!

For smart key, please click START button once.

VIN number was read out, press “OK”.

Record the password: 4034, press “OK”.

xhorse key tool plus Chevy Cruze 2010-2016 Key 4

xhorse key tool plus Chevy Cruze 2010-2016 Key 5

xhorse key tool plus Chevy Cruze 2010-2016 Key 6

xhorse key tool plus Chevy Cruze 2010-2016 Key 7

Add Key

Go back to previous menu on VVDI Key Tool Plus, press

Cruze >> 2010-2016 >> Smart key programming >> Start programming >> Smart keys adding

Operate according to instructions:

Turn on ignition switch(don’t brake, press start button and hold it for about 8s, until the instrument is lit completely)

Put the XSKF21EN Universal Key in the glove box key slot, take other keys out of the car!

OK >> OK

Enter 4-digit password: 4034, press “OK”.

xhorse key tool plus Chevy Cruze 2010-2016 Key 8

xhorse key tool plus Chevy Cruze 2010-2016 Key 9

xhorse key tool plus Chevy Cruze 2010-2016 Key 10

xhorse key tool plus Chevy Cruze 2010-2016 Key 11

It’s performing the requested operation, still need to wait for 10 minutes…

Click START button twice for 2s each time within 5s.

The current key programmed successfully!

Press “OK” to program next one, press “Cancel” to complete.

After press “OK”, click START button.

Keep pressing START button for 5s…

Release the START button, press “OK”.

Keep pressing the START button until instrument light up(if instrument does not light, keep pressing START button for about 15s), then release.

Switch ignition off!

Open then close the driver door, make sure all appliances are off.

Remove the smart key, click both UNLOCK and LOCK button one time, then release.

IMMO device programmed successfully, please use keys to check engine start situation!

If the IMMO light is on, please try to power off the battery.

xhorse key tool plus Chevy Cruze 2010-2016 Key 12

xhorse key tool plus Chevy Cruze 2010-2016 Key 13

xhorse key tool plus Chevy Cruze 2010-2016 Key 14

xhorse key tool plus Chevy Cruze 2010-2016 Key 15

xhorse key tool plus Chevy Cruze 2010-2016 Key 16

Test the new key, it does work well.

Done!

This is how to add a key for Chevy Cruze 2010-2016 with VVDI Key Tool Plus via OBD.

https://www.vvdishop.com/

http://blog.vvdishop.com/xhorse-vvdi-key-tool-plus-adds-chevy-cruze-2016-id46-key/

Comments

Where to Get VAG MQB Sync Data for VVDI Key Tool Plus?

New user report: Made MQB Skoda Octavia 2018 all keys lost with xhorse tools. Tested VVDI Prog and VVDI key tool plus read MQB dashboard. Both devices have bought the new VAG MQB license . Without you cannot read the data on dashboard. and you need internet connection when you start to read the dashboard. Because device confirm you have license before start the reading. There is a e-mail that responded fast and asked sync data for there 60$ cost and get data in less then 3min. email address: sync_data_calcu@qq.com I done already few with 100% success. Lifting pin not very dangerous. They answered fast usually I communicate via wechat and there have take time. Same place need to solder if use key tool plus . But key tool plus does not need 1k oom and no extra 12v as vvdi prog. 2019 build year Skoda Superb akl situation made successfully today. same dashboard 160€ and they give you all data what need to make key. Just force ignition on and read over obd information like on pict

How to Add Key 2019 VW POLO MQB49/5C by Xhorse VVDI Key Tool Plus

Today 2019 VW POLO MQB49/5C add key success. Used Xhorse vvdi key tool plus pad for the whole process. Add key mqb platform (Johnson cluster and new MQB49/5C type on key tool plus are online. Read data with pad, then sent it for online calculation (cost 1 token – must be charged before). You have to use a token to add a spare key from working key. After 3 minutes I got immo data file which automatically saved into the device. After that you make dealer key (used Xhorse proxy MQB style) and program to the car as usual. Test report from Mr. Hrdina.

Read MQB48 RH850 RF701401 Dash by VVDI Key Tool Plus

Another Xhorse RH850 adapter tutorial: how to read VAG MQB NEC35XX RH850 DF701401 dashboard with xhorse vvdi key tool plus and RH850 cable. Procedure: Select Immo Programming>>VW>>Select by Type>>MQB Immo System>>Dashboard-MQB48 (VDO/JCI-NEC35XX Locked)-> Read NEC35XX Chip>>Soldering>>R7F701401 Check wiring diagram Remove components and solder rh850 cable with cluster Connect rh850 cable with key tool plus Read and save immo data Select Get Immo data Upload rh850 DF702401 data save above to calculate immo data Then save immo data Now you can generate dealer key or learn key with the immo data www.vvdishop.com

Xhorse VVDI Key Tool Plus Pad

Search This Blog