VVDI Key Tool Plus Program BMW 320D 2013 FEM AKL

Purpose: Using Xhorse VVDI Key Tool Plus Pad to program a key for BMW 320D 2013 FEM/BDC when all key lost on bench.

Preparation

Remove FEM/BDC from BMW, connect it with FEM platform & Key Tool Plus.

VVDI Key Tool Plus Program BMW 320D 2013 FEM AKL 1

Read key info

Go to Key Tool Plus tablet,

IMMO programming >> Europe >> BMW >> Select from system >> FEM/BDC IMMO system >> Key function >. Start programming

Read key information >> Continue >> Continue

The Key 3 position is blank.

Note: prepare dealer key and reset KM require programming FEM/BDC, enable key and disable key no need programming FEM/BDC!

VVDI Key Tool Plus Program BMW 320D 2013 FEM AKL 2

VVDI Key Tool Plus Program BMW 320D 2013 FEM AKL 3

VVDI Key Tool Plus Program BMW 320D 2013 FEM AKL 4

Program FEM/BDC

Programming FEM/BDC system >> Process Wizard mode >> Begin

Open FEM/BDC module, read EEPROM dump via programmer.

To view the 95128/95256 chip position, press

OK >> OK

VVDI Key Tool Plus Program BMW 320D 2013 FEM AKL 5

VVDI Key Tool Plus Program BMW 320D 2013 FEM AKL 6

VVDI Key Tool Plus Program BMW 320D 2013 FEM AKL 7

VVDI Key Tool Plus Program BMW 320D 2013 FEM AKL 8

Whether to use Xhorse Key Tool Plus prog function to write service mode data? Yes

Remove the EEPROM, connect it to Key Tool Plus via EEPROM adapter.

Make sure the adapter and chip connected, press “Continue”.

Read successfully, rename and press “OK”.

Make sure the adapter and chip connected, press “Continue”.

Please restore FEM/BDC system, provide +12v and connect OBD,

Press “Yes” to continue.

Restore EEPROM and connect the FEM.

VVDI Key Tool Plus Program BMW 320D 2013 FEM AKL 9

VVDI Key Tool Plus Program BMW 320D 2013 FEM AKL 10

VVDI Key Tool Plus Program BMW 320D 2013 FEM AKL 11

Open FEM/BDC shell, write the original EEPROM data read in the step2 to 95128/95256 chip, press “Yes” to continue.

Remove the EEPROM, connect it again to Key Tool Plus via EEPROM adapter.

Make sure the adapter and chip connected, press “Continue”.

Restore EEPROM and connect the FEM.

Write successfully, please restore FEM/BDC system, power and connect OBD.

Continue after finish.

Press “OK”.

Do you want to verify the write coding? Press “Yes”.

FEM/BDC programming success, you can make new dealer key from the main window!

OK >> Exit

VVDI Key Tool Plus Program BMW 320D 2013 FEM AKL 12

VVDI Key Tool Plus Program BMW 320D 2013 FEM AKL 13

VVDI Key Tool Plus Program BMW 320D 2013 FEM AKL 14

Program key

Go to “Prepare dealer key with ignition switch” >> Select a blank key position: Key 3

Note:

For all key lost, read ISN from ECU;

For adding key, read ISN from working key.

VVDI Key Tool Plus Program BMW 320D 2013 FEM AKL 15

VVDI Key Tool Plus Program BMW 320D 2013 FEM AKL 16

Known ISN >> Input ISN value >> OK

Insert a new key to ignition switch, turn on or put it close to emergency start position.

Press “OK”.

Key learn success!

Go to read key information again, Key 3 is with data now.

VVDI Key Tool Plus Program BMW 320D 2013 FEM AKL 17

VVDI Key Tool Plus Program BMW 320D 2013 FEM AKL 18

VVDI Key Tool Plus Program BMW 320D 2013 FEM AKL 19

VVDI Key Tool Plus Program BMW 320D 2013 FEM AKL 20

Key programming has done!

This is BMW 320D 2013 FEM/BDC all key lost key programming via VVDI Key Tool Plus successfully!

https://www.vvdishop.com/

Comments

Where to Get VAG MQB Sync Data for VVDI Key Tool Plus?

New user report: Made MQB Skoda Octavia 2018 all keys lost with xhorse tools. Tested VVDI Prog and VVDI key tool plus read MQB dashboard. Both devices have bought the new VAG MQB license . Without you cannot read the data on dashboard. and you need internet connection when you start to read the dashboard. Because device confirm you have license before start the reading. There is a e-mail that responded fast and asked sync data for there 60$ cost and get data in less then 3min. email address: sync_data_calcu@qq.com I done already few with 100% success. Lifting pin not very dangerous. They answered fast usually I communicate via wechat and there have take time. Same place need to solder if use key tool plus . But key tool plus does not need 1k oom and no extra 12v as vvdi prog. 2019 build year Skoda Superb akl situation made successfully today. same dashboard 160€ and they give you all data what need to make key. Just f...

Read MQB48 RH850 RF701401 Dash by VVDI Key Tool Plus

Another Xhorse RH850 adapter tutorial: how to read VAG MQB NEC35XX RH850 DF701401 dashboard with xhorse vvdi key tool plus and RH850 cable. Procedure: Select Immo Programming>>VW>>Select by Type>>MQB Immo System>>Dashboard-MQB48 (VDO/JCI-NEC35XX Locked)-> Read NEC35XX Chip>>Soldering>>R7F701401 Check wiring diagram Remove components and solder rh850 cable with cluster Connect rh850 cable with key tool plus Read and save immo data Select Get Immo data Upload rh850 DF702401 data save above to calculate immo data Then save immo data Now you can generate dealer key or learn key with the immo data www.vvdishop.com

Will VVDI Key Tool Plus Program VAG MQB49 Key

How to program VAG MQB49 key with xhorse vvdi key tool plus ? This is a frequently asked question. Here’s the clue. Only Johnson Control instrument is supported by xhorse . Xhorse key tool plus or vvdi2 will only add key to MQB49 (still need sync data), they cannot do MQB49 all keys lost. 1. Calculate immo data online Try to read immo data with key tool plus, if failed to read immo data (shown as error image below). You need to obtain sync data from 3rd party. 2 Check immo status Display the number of vehicle keys, whether current key is locked and whether is dealer key and other information 3. Generate dealer key Load immo data file to generate dealer key, support generate normal dealer key and OME key (online) 4. Leanr key Learn the new generated key and original key into the car together, keys that are not learned will not be able to start the car. 5. Modify MQB49 key ID

Xhorse VVDI Key Tool Plus Pad

Search This Blog